This is the README for chan_ss7, version 0.9 Copyright (C) 2006-2017 Netfors ApS. chan_ss7 is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. A copy of the GPL is included in the file COPYING. The chan_ss7 module implements SS7 connectivity for Asterisk. Major features include - MTP2 (Q.703) implementation (mostly complete). - MTP3 (Q.704) implementation (bare essentials). - ISUP (Q.76x) implementation (reasonable subset). - Supports Digium E1 (T1 and other zap-compatible cards should be easy to add). - Supports incoming and outgoing calls. - Supports full ALAW audio (ULAW should be easy to add). - Facilities for raw MTP2 packet dump, suitable for Ethereal debugging. - Open Source (GPL). - Supports high call volumes; tested with 120 simultaneous calls, but should handle much more than that, depending on transcoding etc. - Supports multiple linksets with different DPCs - Supports linksets with multiple links. - Supports load sharing and MTP changeover. - Supports multiple hosts (cluster) configuration with load sharing and failover. - Flexible Dial command syntax for SS7 to allow use on linksets, e.g. Dial(SS7/linkset1/12345678) New in version 0.9 - Major refactoring of source code to support other level 4 protocols - Dynamic adjustment of audio data buffers during writes - this should reduce "write buffer full" problems - New CLI command: ss7 show channels, same as ss7 linestat - Initial address message can be broken to IAM and subsequent SAMs - Fixed crash when executing CLI reset command - Tested with asterisk version 1.2.9. New in version 0.8.4 - Fixed crash when T1 expires - Made check on audio read to detect underruns - Fixed crash in process_acm - Changed priority for continuity check thread - Fixed crash in CLI command block/unblock - Fixed CLI command output: "Unknown state: 3" - Listen on cluster socket only when there are other cluster nodes configured - Port for TCP connection in cluster now configurable - Use of ast_setstate to report channel state changes - New per link config options to enable echo cancellation in Zaptel driver - New CIC hunting policies: sequential low-to-high and sequential high-to-low New in version 0.8.3 - Fixed propagation of release causes to/from asterisk - Reply with UEC when receiving messages from unknown peers - Make t35 value configurable, and action upon timeout selectable (Timeout/End-of-pulsing) - Redirecting number and redirection information are now included in IAM when present - The optional backward call indicators allways has 'In-band information indication'. If chan_ss7 has not detected any other source of in-band information, it generates it - Enhanced dial command syntax: Dial(SS7/number:redirecting-number), allows a redirecting number to be inserted into IAM New in version 0.8.2 - Handling of suspend/resume New in version 0.8.1 - Introduced subservice configuration option for linksets. - Fixed bug that causes crash when received CGU and other circuit group messages - Fixed bug that causes repeat warning when doing continuity check - Fixed a problem with the initial alignment procedure - Tested with asterisk version 1.2.4. New in version 0.8 - Multiple links with load sharing and MTP changeover - Multiple linksets and multiple peers - Multiple hosts (cluster) with failover capability - Multiple interconnects (TCP/IP) between hosts for redundant communication links - Additional supported ISUP messages - Circuit group unblocking - Circuit group unblocking acknowledge - Single circuit reset - Single circuit blocking - Single circuit unblocking - Continuity check request - Continuity - Subsequent address message - Sending of address complete message - Sending of answer message - New UI ss7 commands: link status, linestat, cluster {start,stop,status} - Partial support for continuity check - Partial support for overlapped dialling (IAM, subsequent SAMs) The configuration file format has changed, please refer to the different ss7.conf.template.* example configuration files. It is designed such that the same file can be used in a multi host setup. Report any problems or successes to chan-ss7@netfors.com.